top of page

Handrail Height in NZ: What the Building Code Requires

Writer: Rudi Visser
Rudi Visser
5 days ago
10 min read

Handrail following a timber staircase in an Auckland home

For a stair in a New Zealand home, the handrail goes between 900 mm and 1000 mm above the pitch line, the imaginary line that joins the front edges (nosings) of the treads. That is the Acceptable Solution D1/AS1 position, and it is the number a building consent officer will look for. This guide shows how to measure it, where a handrail is needed, how it differs from a barrier or deck balustrade, and what to check before you alter a stair in your own home.



TL;DR

 

  • Stair handrail height in a house: 900 mm to 1000 mm, measured vertically from the pitch line (the nosings of the treads).

  • Handrails are required on all stairs, except a stair in a household unit with three risers or fewer, where one is still a good safety feature.

  • A stair barrier (the guard that stops a fall off the side) must be at least 900 mm high in a house. Balconies and decks need at least 1000 mm.

  • The handrail must be continuous down each flight, follow the slope of the stair and be easy to grip.

  • Check consent before you change a stair or deck. We manage the consent process and the trades for renovations in Auckland.

 

Table of Contents

 

 

The handrail height rule for NZ homes

 

New Zealand has one national Building Code, so the same rule applies in Auckland, Dunedin and everywhere between. The Code itself sets performance outcomes. The numbers most homeowners and builders work to come from Acceptable Solution D1/AS1, a document that describes one pathway that is deemed to comply. The current edition of D1/AS1 is the 2nd edition, amendment 6, effective 1 January 2017.

 

Under D1/AS1, the handrail on a stair is positioned between 900 mm and 1000 mm above the pitch line. That gives a 100 mm window. Any height inside it complies. Most people pick a height in the middle, but the choice often comes down to how the handrail meets the posts, the newel and the wall.

 

A designer can propose an Alternative Solution, which may carry different numbers, so the D1/AS1 figures are the standard path, not the only legal one. For a typical house renovation, the standard path is the sensible one because it is what council staff check against.


The handrail height rule for NZ homes

How to measure handrail height on a stair

 

Most mistakes happen here, because people measure from the floor or from the middle of a tread. Use this routine:

 

  1. Find the nosings. The nosing is the leading edge of each tread. Lay a straight edge or stretch a string across the nosings of at least three steps. That line is the pitch line.

  2. Measure vertically. Hold the tape plumb, not at right angles to the slope. Barrier and handrail heights on stairs are measured vertically from the pitch line or stair nosings.

  3. Read the top of the handrail. The top surface you grip must sit between 900 mm and 1000 mm above the line.

  4. Check several points. Measure at the top, middle and bottom of the flight. The handrail should have the same slope as the pitch line, so the readings should match.

  5. Allow for finishes. On floors, landings and ramps, height is measured from the finished floor level, ignoring carpet or vinyl. If you are about to lay new flooring, measure to the structural floor, or check the landing again afterwards.

 

A worked example: a straight flight has nosings that are 190 mm apart vertically. A handrail fixed with its top surface 930 mm above the line at the first nosing and 930 mm above the line at the last nosing complies. One that reads 930 mm at the bottom and 860 mm at the top has drifted and needs to be refixed.

 

Where a stair handrail is required

 

D1/AS1 requires handrails on all stairs. There is one exception that matters in homes: a stair in a household unit with three risers or fewer does not need a handrail, although adding one is a safety gain, particularly for children and older people. A short flight at a front door is the usual case.

 

Other points on a compliant handrail:

 

  • It runs continuously from the top to the bottom of each flight.

  • It follows the slope of the pitch line.

  • It can be fixed to a wall or sit on top of a stair barrier.

 

Handrail, barrier and balustrade: three different jobs

 

Homeowners often mix these terms up, and the numbers differ.

 

  • Handrail: the part you hold for support while going up or down.

  • Barrier (balustrade): the guard that stops people falling off the open edge of a stair, landing or deck.

  • Both in one: on many stairs the handrail sits on top of the barrier and does both jobs.

 

F4/AS1 Table 1 (3rd edition, amendment 2, effective 1 January 2017) sets the minimum barrier height in detached dwellings and household units at:

 

Location in a house

Minimum barrier height

Stairs, ramps and their intermediate landings

900 mm

Balconies, decks, and edges of internal or mezzanine floors

1000 mm

In buildings other than housing, and in the common areas of multi-unit dwellings, the figures are 900 mm on stairs and ramps and 1100 mm in most other places. A handrail mounted on a stairway barrier in those buildings may rise to 1100 mm over a transition zone of about 300 mm on the intermediate landing. MBIE explains that a handrail’s purpose is safety on the flight, so its height on a landing is not critical. Most homeowners will never need this detail, but it explains why you see handrails that step up at landings in apartment blocks and commercial buildings.

 

Gaps in the barrier

 

Height is only part of a safe barrier. Where children under six are likely to be present, which includes ordinary homes, F4/AS1 requires that a barrier offers no easy or obvious means of climbing, has no toe-holds between 150 mm and 760 mm above the floor, and has no opening that lets a 100 mm sphere pass through. The one exception is the triangular gap formed by the riser, tread and bottom rail on a stair, where a 150 mm sphere is the largest that may pass.

 

This is why horizontal rails and wide-spaced balusters are a problem on stairs and decks in family homes, even when the height is right.


Gaps in the barrier

Handrails on decks and balconies

 

A deck is not a stair, so the stair figure of 900 to 1000 mm does not apply. Clause F4 requires a barrier where people could fall 1 metre or more. Below that height the Code does not require one, but if you install one it still needs to be safe. In a house the barrier on a deck needs to be at least 1000 mm high, as the table above shows.

 

If the ground slopes gradually away from the deck, MBIE guidance (Determination 2008/81) suggests measuring the height of fall 1200 mm out from the deck edge, not at the edge itself. That can push a deck that looks low over the 1 metre line.

 

If you have a deck project in mind, our guide to deck consent in NZ covers when consent is needed.

 

Handrail shape, clearance and ends

 

A handrail at the right height can still fail if it is hard to hold. Three checks:

 

  • Profile. Handrails must be easy to grasp. The optimum profile is a 40 mm round section, and D1/AS1 specifies cross-section dimensions. A flat timber top rail that you cannot wrap your hand around is a common reason for a fail.

  • Clearance from the wall. For accessible routes, BRANZ lists 45 to 60 mm of uninterrupted clearance from a wall or structure, and a diameter of 32 to 50 mm.

  • Ends. The ends of accessible handrails should be turned down at least 100 mm or returned into the wall, so a sleeve or a bag strap cannot catch on them.

 

The BRANZ guidance on accessibility hardware puts accessible stair and ramp handrails at 900 to 1000 mm above the floor, with a 300 mm horizontal extension past the last riser at each end. It notes that these details are good universal design and the extension is useful in houses where there is room. If you are planning for a family member who is getting older, building these in now is far cheaper than retrofitting. Our accessible bathroom design guide covers the same thinking for wet areas.

 

Stair geometry that goes with handrail height

 

Handrail height is measured from the pitch line, so it only works if the stair itself is right. For a main private stair in a house, D1/AS1 sets a maximum riser height of 190 mm, a minimum tread depth of 280 mm and a maximum pitch of 37°. If the stringers are cut wrong, fixing the geometry later means cutting in the entire stringer, and the handrail measurements go with it. Confirm the stair type from the plans and write its limits on the stringer template before cutting.

 

Older homes bring a different problem: the stair is not square, the treads have worn, or a curved stair needs matching repair work. Specialists in curved stair repair and matching show how much careful assessment a stair needs before any new rail is fitted to it.

 

Consent, and what needs checking before you start

 

Whether you need building consent depends on what you are changing.

 

  • Handrails: Enable New Zealand classes custom-made internal and external handrails as minor modifications that do not require building consent, while decks or landings more than 1 m high do.

  • Decks: a deck no more than 1.5 metres above the supporting ground, with no other consent trigger, is exempt under Schedule 1 of the Building Act 2004. Above that height, or if the deck affects structure or weathertightness, consent is needed.

  • Exempt is not exempt from the Code. Even a consent-free deck must still meet the Building Code, including the 1 metre barrier rule under F4.

 

Before any stair or handrail work in your home, run through this list:

 

  1. Measure from the pitch line and confirm 900 to 1000 mm.

  2. Check that the barrier is at least 900 mm on the stair and 1000 mm on any deck or balcony, with no gaps that let a 100 mm sphere through.

  3. Confirm the handrail is continuous, follows the slope and can be gripped.

  4. Check how the handrail is fixed to the posts or wall. A rail at the right height that moves under load is not a safe rail.

  5. If you are altering the stair itself, or the work touches structure, ask the council whether consent is needed.

 

If your renovation also touches other safety items, our guides to smoke alarm placement and RCD requirements are worth reading in the same planning pass.

 

Mistakes that cause a failed inspection

 

  • Measuring from the floor of the landing or the middle of a tread instead of the nosing line.

  • Fixing the rail before the final floor finish, so the carpet or flooring changes the landing height.

  • Using a flat or oversized top rail that is hard to grip.

  • Stopping the handrail short of the bottom or top step so there is no continuous support.

  • Spacing balusters too widely for a family home.

  • Treating a deck like a stair, and fitting a 900 mm barrier where 1000 mm is required.

 

Each of these is cheap to fix before the stair is finished and expensive after.

 

  Handrail height looks like a one-line rule, yet it is tied to the stair geometry, the floor finishes and the barrier. A rail that is correct on paper can be wrong by the time the flooring goes down.   That is why we treat a stair as part of the whole renovation, not as a separate small job. Our approach is one team, all trades and one point of contact, so the carpenter, the flooring installer and the painter work to the same measurements, and the building consent process is handled for you.   For first-time buyers, the best moment to settle handrails, barriers and deck edges is before the scope and fixed-fee quote are agreed, not after the inspection.   Rudi

Our view: get the stair right once

 

When the stair is part of a bigger renovation

 

If your handrail, stair or deck edge is one piece of a larger project, it is easier to have one team manage it. Sorted Home Solutions handles home renovation and repair in Auckland, with all trades under one team, the building consent process managed, and fixed-fee quotes. You can see what is covered on our Full Home Reno page, or look at the smaller jobs on our services page.


Sortedhomesolutions

To discuss your project, start at sortedhomesolutions.co.nz.

 

FAQ

 

What is the minimum handrail height for stairs in NZ?

 

In a house, the handrail must be between 900 mm and 1000 mm above the pitch line, so the lowest compliant top surface is 900 mm. The pitch line joins the nosings of the treads, and the measurement is vertical.

 

Do I need a handrail on every staircase?

 

D1/AS1 requires handrails on all stairs, but a stair in a household unit with three risers or fewer does not need one. Fitting one is still sensible, especially where children or older people use the steps.

 

How high should a deck balustrade be?

 

In a house, F4/AS1 sets a minimum barrier height of 1000 mm on decks and balconies. A barrier is required where the fall could be 1 metre or more, and any openings must stop a 100 mm sphere from passing through.

 

Do I need building consent to replace a handrail?

 

Custom-made internal and external handrails are treated as minor modifications that do not need consent. Decks or landings over 1 m high, and any work that affects structure, are different, so check with your council before starting.

 

Can the numbers differ from the ones in this guide?

 

The figures here are the Acceptable Solution path. A designer can propose an Alternative Solution with different numbers, which the council must accept as meeting the Code. For a typical home renovation, working to the standard numbers is the simplest route.

 

Sources

 

Recommended

 

 
 
 

Comments


bottom of page